COOLON-HIGH POWER RGB PWM TREIBER

COOLON-HIGH POWER RGB PWM DRIVER DETAILS:

Type: Driver
File Name: coolon_high_33024.zip
File Size: 12.0 MB
Rating:
4.07
18 (4.07)
Downloads: 11
Supported systems: Windows Vista, Windows Vista 64-bit, Windows XP 64-bit, Mac OS X, Mac OS X 10.4, Mac OS X 10.5
Price: Free* (*Free Registration Required)

Download Now
COOLON-HIGH POWER RGB PWM DRIVER



If no signal is applied to the PWM signal cables, the drivers go to full brightness.

DRIVERS: COOLON-HIGH POWER RGB PWM

You can also connect a Coolon-high power rgb pwm to the signal input to adjust brightness at least the datasheet states so of each channel. Do not test extensively now, the LEDs cannot handle the heat without the heatsink. So let's attach it Clean the heatsink from any stickers and oil that may still be on them. Apply some heat sink compound to the center, where the LED will be placed.

Put the LED on top and press it down. Remove any excess heat sink paste that may come out on the sides.

Approx 5x Coolon-High Power RGB PWM DRIVER with DMX

The LED should now hold on the heatsink on the greasy paste. I used two component epoxy glue to secure it. This surely is not the best method, it would be better to use screws, the glue weakens over time due to the elevated temperature and the LED can become loose. For the ones that became loos I then used a silicone glue instead of the heatsink paste, which also works fine but if available, use screws! You may notice that in the coolon-high power rgb pwm there is a lot of debris. That is from the plastic lens that was on top of the LED.

Coolon-high power rgb pwm the reflector is put directly on to the LED, the color mixing is just awful. So we need to scramble the colors. To this purpouse I added the color mixing chamber. The light from the LED passes through the first diffuse surface, gets reflected and scrambled inside the tube and passes through another diffusor, scrambling it even more.

Triple Output High Power RGB LED - COM - SparkFun Electronics

This reduces the brightness of the LEDs a lot, but makes for a nice and smooth spot light. Ok, so cut the 20mm pipe into pieces of the same length of about mm. Use sand paper to make them nice and flat. Use the dremel tool with some polishing paste to polish the inside of the coolon-high power rgb pwm of tube.

COOLON-HIGH POWER RGB PWM WINDOWS 8.1 DRIVER DOWNLOAD

Glue the diffuser milk glass, scotch tape Glue the whole mixing chamber on to the LEDs. I used epoxy glue for this, but it does not stick too well to the plastic of the LED and I often had to do it twice or three times because it broke off during the assembly of the lamp. The reflector was intended to use on a much small LED, coolon-high power rgb pwm the hole in the center is only mm.

  • 1W High Power RGB LED
  • Chained Mood-light Using High Power RGB LEDs: 11 Steps (with Pictures)
  • High Power 3W RGB LED :: Solarbotics
  • Chained Mood-light Using High Power RGB LEDs
  • High Power 3W RGB LED

Use a vice to hold the reflector and carefully make the hole bigger. The systems allows you to create original 8-bit sounds programmed and controlled via the Arduino board. Active high or low buttons, software debounced.

Check this project too: Of course, this also depends on the accuracy of my own visual perception. Quantity Required Add to Cart. Related Books. Raspberry Pi.

Data Logging.COOLON-HIGH POWER RGB PWM DRIVER - The interface can sense buttons, rotary encoders, keypads, analog buttons, serial keypads or even smartphone. dc v - coolon-high power rgb pwm channel rgb pwm driver - rgb controller pwm - kuantum 16 Channel dmx decoder led.

COOLON-HIGH POWER RGB PWM DRIVER DOWNLOAD.

Relevant Posts